Quick ?s
Cheat Sheets
Man Pages
The Lynx

       traceroute - print the route packets take to network host

       traceroute [ -dFIlnrvx ] [ -f first_ttl ] [ -g gateway ]
	       [ -i iface ] [ -m max_ttl ] [ -p port ]
	       [ -q nqueries ] [ -s src_addr ] [ -t tos ]
	       [ -w waittime ] [ -z pausemsecs ]
	       host [ packetlen ]

       The  Internet  is  a large and complex aggregation of network hardware,
       connected together by gateways.	Tracking the route ones packets  fol
       low  (or  finding the miscreant gateway thats discarding your packets)
       can be difficult.  Traceroute utilizes the IP protocol time  to	live
       field  and  attempts to elicit an ICMP TIME_EXCEEDED response from each
       gateway along the path to some host.

       The only mandatory parameter is the destination host name or IP number.
       The  default  probe  datagram  length  is  40  bytes,  but  this may be
       increased by specifying a packet length (in bytes) after  the  destina
       tion host name.

       Other options are:

       -f     Set  the	initial  time-to-live used in the first outgoing probe

       -F     Set the "dont fragment" bit.

       -d     Enable socket level debugging.

       -g     Specify a loose source route gateway (8 maximum).

       -i     Specify a network interface to obtain the source IP address  for
	      outgoing probe packets. This is normally only useful on a multi-
	      homed host. (See the -s flag for another way to do this.)

       -I     Use ICMP ECHO instead of UDP datagrams.

       -l     Display the ttl value of the returned packet.   This  is	useful
	      for checking for assymetric routing.

       -m     Set  the	max time-to-live (max number of hops) used in outgoing
	      probe packets.  The default is 30 hops (the  same  default  used
	      for TCP connections).

       -n     Print  hop  addresses  numerically  rather than symbolically and
	      numerically (saves a nameserver address-to-name lookup for  each
	      gateway found on the path).

       -p     Set  the base UDP port number used in probes (default is 33434).
	      Traceroute hopes that nothing is listening on UDP ports base + 1
	      to   base   +   nhops  at  the  destination  host  (so  an  ICMP
	      PORT_UNREACHABLE message will be returned to terminate the route
	      tracing).   If  something  is listening on a port in the default
	      range, this option can be used to pick an unused port range.

       -r     Bypass the normal routing tables and send directly to a host  on
	      an  attached network.  If the host is not on a directly-attached
	      network, an error is returned.  This option can be used to  ping
	      a  local	host through an interface that has no route through it
	      (e.g., after the interface was dropped by routed(8C)).

       -s     Use the following IP address (which usually is given  as	an  IP
	      number,  not a hostname) as the source address in outgoing probe
	      packets.	On multi-homed hosts (those  with  more  than  one  IP
	      address), this option can be used to force the source address to
	      be something other than the IP  address  of  the	interface  the
	      probe  packet  is  sent on.  This option can only be used by the
	      super-user.  (See the -i flag for another way to do this.)

       -t     Set the type-of-service in probe packets to the following  value
	      (default	zero).	 The  value  must  be a decimal integer in the
	      range 0 to 255.  This option can be used	to  see  if  different
	      types-of-service	result	in  different  paths.  (If you are not
	      running 4.4bsd, this may be academic since  the  normal  network
	      services	like  telnet  and  ftp dont let you control the TOS).
	      Not all values of TOS are legal or meaningful - see the IP  spec
	      for definitions.	Useful values are probably -t 16 (low delay)
	      and -t 8 (high throughput).

       -v     Verbose output.  Received ICMP packets other than  TIME_EXCEEDED
	      and UNREACHABLEs are listed.

       -w     Set  the	time  (in  seconds)  to wait for a response to a probe
	      (default 5 sec.).

       -x     Toggle ip checksums. Normally,  this  prevents  traceroute  from
	      calculating  ip  checksums.  In some cases, the operating system
	      can overwrite parts of the outgoing packet but  not  recalculate
	      the  checksum  (so in some cases the default is to not calculate
	      checksums and using -x causes them to be calcualted). Note  that
	      checksums  are usually required for the last hop when using ICMP
	      ECHO probes (-I).  So they  are  always  calculated  when  using

       -z     Set  the time (in milliseconds) to pause between probes (default
	      0).  Some systems such as Solaris and  routers  such  as	Ciscos
	      rate  limit icmp messages. A good value to use with this this is
	      500 (e.g. 1/2 second).

       This program attempts to trace the route an IP packet would  follow  to
       some  internet  host  by  launching  UDP probe packets with a small ttl
       (time to live) then listening for an ICMP "time exceeded" reply from  a
       gateway.   We  start  our  probes with a ttl of one and increase by one
       until we get an ICMP "port unreachable" (which means we got to  "host")
       or  hit	a  max (which defaults to 30 hops & can be changed with the -m
       flag).  Three probes (change with -q flag) are sent at each ttl setting
       and a line is printed showing the ttl, address of the gateway and round
       trip time of each probe.  If the  probe	answers  come  from  different
       gateways,  the  address	of each responding system will be printed.  If
       there is no response within a 5 sec. timeout interval (changed with the
       -w flag), a "*" is printed for that probe.

       We  dont want the destination host to process the UDP probe packets so
       the destination port is set to an unlikely value (if some clod  on  the
       destination is using that value, it can be changed with the -p flag).

       A sample use and output might be:

	      [yak 71]% traceroute nis.nsf.net.
	      traceroute to nis.nsf.net (, 30 hops max, 38 byte packet
	       1  helios.ee.lbl.gov (  19 ms  19 ms  0 ms
	       2  lilac-dmc.Berkeley.EDU (  39 ms	39 ms  19 ms
	       3  lilac-dmc.Berkeley.EDU (  39 ms	39 ms  19 ms
	       4  ccngw-ner-cc.Berkeley.EDU (  39 ms  40 ms  39 ms
	       5  ccn-nerif22.Berkeley.EDU (  39 ms  39 ms  39 ms
	       6 (  40 ms  59 ms  59 ms
	       7 (  59 ms  59 ms  59 ms
	       8 (  99 ms	99 ms  80 ms
	       9 (  139 ms  239 ms  319 ms
	      10 (  220 ms  199 ms  199 ms
	      11  nic.merit.edu (  239 ms  239 ms  239 ms

       Note  that  lines 2 & 3 are the same.  This is due to a buggy kernel on
       the 2nd hop system - lbl-csam.arpa - that forwards packets with a  zero
       ttl  (a	bug in the distributed version of 4.3BSD).  Note that you have
       to guess what path the  packets	are  taking  cross-country  since  the
       NSFNet  (129.140)  doesnt  supply address-to-name translations for its

       A more interesting example is:

	      [yak 72]% traceroute allspice.lcs.mit.edu.
	      traceroute to allspice.lcs.mit.edu (, 30 hops max
	       1  helios.ee.lbl.gov (  0 ms  0 ms  0 ms
	       2  lilac-dmc.Berkeley.EDU (  19 ms	19 ms  19 ms
	       3  lilac-dmc.Berkeley.EDU (  39 ms	19 ms  19 ms
	       4  ccngw-ner-cc.Berkeley.EDU (  19 ms  39 ms  39 ms
	       5  ccn-nerif22.Berkeley.EDU (  20 ms  39 ms  39 ms
	       6 (  59 ms  119 ms  39 ms
	       7 (  59 ms  59 ms  39 ms
	       8 (  80 ms	79 ms  99 ms
	       9 (  139 ms  139 ms  159 ms
	      10 (  199 ms  180 ms  300 ms
	      11 (  300 ms  239 ms  239 ms
	      12  * * *
	      13 (  259 ms  499 ms  279 ms
	      14  * * *
	      15  * * *
	      16  * * *
	      17  * * *
	      18  ALLSPICE.LCS.MIT.EDU (  339 ms  279 ms  279 ms

       Note that the gateways 12, 14, 15, 16 & 17 hops away either dont  send
       ICMP  "time  exceeded"  messages  or  send them with a ttl too small to
       reach us.  14 - 17 are running the MIT C Gateway code that doesnt send
       "time exceeded"s.  God only knows whats going on with 12.

       The  silent  gateway  12 in the above may be the result of a bug in the
       4.[23]BSD network code (and its derivatives):  4.x (x <=  3)  sends  an
       unreachable  message  using  whatever ttl remains in the original data
       gram.  Since, for gateways, the remaining ttl is zero, the  ICMP  "time
       exceeded"  is  guaranteed  to  not make it back to us.  The behavior of
       this bug is slightly more interesting when it appears on  the  destina
       tion system:

	       1  helios.ee.lbl.gov (  0 ms  0 ms  0 ms
	       2  lilac-dmc.Berkeley.EDU (  39 ms	19 ms  39 ms
	       3  lilac-dmc.Berkeley.EDU (  19 ms	39 ms  19 ms
	       4  ccngw-ner-cc.Berkeley.EDU (  39 ms  40 ms  19 ms
	       5  ccn-nerif35.Berkeley.EDU (  39 ms  39 ms  39 ms
	       6  csgw.Berkeley.EDU (  39 ms  59 ms  39 ms
	       7  * * *
	       8  * * *
	       9  * * *
	      10  * * *
	      11  * * *
	      12  * * *
	      13  rip.Berkeley.EDU (  59 ms !  39 ms !  39 ms !

       Notice  that  there are 12 "gateways" (13 is the final destination) and
       exactly the last half of them are "missing".  Whats  really  happening
       is  that  rip  (a  Sun-3  running  Sun OS3.5) is using the ttl from our
       arriving datagram as the ttl in its ICMP reply.	 So,  the  reply  will
       time out on the return path (with no notice sent to anyone since ICMPs
       arent sent for ICMPs) until we probe with a ttl thats at least twice
       the  path  length.  I.e., rip is really only 7 hops away.  A reply that
       returns with a ttl of 1 is a  clue  this  problem  exists.   Traceroute
       prints  a  "!" after the time if the ttl is <= 1.  Since vendors ship a
       lot of obsolete (DECs Ultrix, Sun 3.x) or  non-standard	(HPUX)	soft
       ware,  expect  to  see this problem frequently and/or take care picking
       the target host of your probes.

       Other possible annotations after the time are !H, !N, or !P (host, net
       work  or  protocol unreachable), !A, !C (access to the network or host,
       respectively, is  prohibited),  !S  (source  route  failed),  !F-
       (fragmentation  needed  -  the RFC1191 Path MTU Discovery value is dis
       played),  !X  (communication  administratively  prohibited),  !V  (host
       precedence  violation),	!C  (precedence  cutoff  in effect), or !
       (ICMP unreachable code ).  These are  defined  by  RFC1812	(which
       supersedes  RFC1716).   If almost all the probes result in some kind of
       unreachable, traceroute will give up and exit.

       This program is intended for use in network  testing,  measurement  and
       management.   It  should  be used primarily for manual fault isolation.
       Because of the load it could impose on the network, it is unwise to use
       traceroute during normal operations or from automated scripts.

       If  your kernel does not support rtnetlink (routing messages), you will
       get a warning of the form
	      traceroute: Warning: findsaddr: error sending netlink message: 
	      traceroute: Warning: ip checksums disabled
       This is harmless as IP checksums will be provided by  the  kernel,  and
       UDP  checksums  (which are also disabled when rtnetlink is unavailable)
       are optional.

       pathchar(8), netstat(1), ping(8)

       Implemented by  Van  Jacobson  from  a  suggestion  by  Steve  Deering.
       Debugged by a cast of thousands with particularly cogent suggestions or
       fixes from C. Philip Wood, Tim Seaver and Ken Adelman.

       The current version is available via anonymous ftp:


       Please send bug reports to traceroute@ee.lbl.gov.

4.3 Berkeley Distribution      21 September 2000		 TRACEROUTE(8)

Yals.net is © 1999-2009 Crescendo Communications
Sharing tech info on the web for more than a decade!
This page was generated Thu Apr 30 17:05:32 2009