Quick ?s
Cheat Sheets
Man Pages
The Lynx
Software
RMT(8)			  BSD System Managers Manual		       RMT(8)

NAME
     rmt - remote magtape protocol module

SYNOPSIS
     rmt

DESCRIPTION
     Rmt is a program used by tar, cpio, mt, and the remote dump and restore
     programs in manipulating a magnetic tape drive through an interprocess
     communication connection.	Rmt is normally started up with an rexec(3) or
     rcmd(3) call or the rsh(1) command.

     The rmt program accepts requests specific to the manipulation of magnetic
     tapes, performs the commands, then responds with a status indication.
     All responses are in ASCII and in one of two forms.  Successful commands
     have responses of:

	   Anumber\n

     Number is an ASCII representation of a decimal number.  Unsuccessful com
     mands are responded to with:

	   Eerror-number\nerror-message\n

     Error-number is one of the possible error numbers described in intro(2)
     and error-message is the corresponding error string as printed from a
     call to perror(3).  The protocol is comprised of the following commands,
     which are sent as indicated - no spaces are supplied between the command
     and its arguments, or between its arguments, and \n indicates that a
     newline should be supplied:

     Odevice\nmode\n
	     Open the specified deviceusing the indicated mode.Deviceis a full
	     pathname and modeis an ASCIIrepresentation of a decimal number
	     suitable for passing to open(2).If a device had already been
	     opened, it is closed before a new open is performed.

     Cdevice\n
	     Close the currently open device.  The devicespecified is ignored.

     Loffset\nwhence\n
	     Perform an lseek(2) operation using the specified parameters.
	     The response value is that returned from the lseek call.

     Wcount\n
	     Write data onto the open device.  Rmt reads count bytes from the
	     connection, aborting if a premature end-of-file is encountered.
	     The response value is that returned from the write(2) call.

     Rcount\n
	     Read count bytes of data from the open device.  If count exceeds
	     the size of the data buffer (10 kilobytes), it is truncated to
	     the data buffer size.  rmt then performs the requested read(2)
	     and responds with Acount-read\n if the read was successful; oth
	     erwise an error in the standard format is returned.  If the read
	     was successful, the data read is then sent.

     Ioperation\ncount\n
	     Perform a MTIOCOP ioctl(2) command using the specified parame
	     ters.  The parameters are interpreted as the ASCII representa
	     tions of the decimal values to place in the mt_op and mt_count
	     fields of the structure used in the ioctl call.  The return value
	     is the count parameter when the operation is successful.

     S	     Return the status of the open device, as obtained with a MTIOCGET
	     ioctl call.  If the operation was successful, an ack is sent
	     with the size of the status buffer, then the status buffer is
	     sent (in binary).

     Any other command causes rmt to exit.

DIAGNOSTICS
     All responses are of the form described above.

SEE ALSO
     tar(1), cpio(1), mt(1), rsh(1), rcmd(3), rexec(3), mtio(4), rdump(8),
     rrestore(8)

BUGS
     People should be discouraged from using this for a remote file access
     protocol.

HISTORY
     The rmt command appeared in 4.2BSD.

4.2 Berkeley Distribution      December 11, 1993     4.2 Berkeley Distribution




Yals.net is © 1999-2009 Crescendo Communications
Sharing tech info on the web for more than a decade!
This page was generated Thu Apr 30 17:05:32 2009